UC知道帮忙翻译一下，英语！！急
来源：百度知道 编辑：UC知道 时间：2024/07/02 22:59:38
Known fixes:
1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement Hybrid - Tighten the GPU screws facing the HANA chip slightly more...
3) Reflowing the solder with a heatgun(Concentrate on the GPU and (H)ANA chip
Related Errors:
0022
Description:
This error is caused by a cold solder joint under the GPU, (H)ANA-chip or in between.Can also be a component that is missing or damaged so look for missing parts near the GPU and the (H)ANA chip.
References:
No references available...
Known fixes:
1)If you worked on the mainboard recently(soldered or so) remove these wires because you might be drawing too much power from the GPU
Also look for missing/bridged components like capacitors/resistors
2) X-Clamp replaceme
1)If you soldered anything to the mainboard before it occured, whatever you are powering from this point is drawing too much power so get rid of it.Also get rid of everything that you can see that might bridge anything near the GPU.
2) X-Clamp replacement Hybrid - Tighten the GPU screws facing the HANA chip slightly more...
3) Reflowing the solder with a heatgun(Concentrate on the GPU and (H)ANA chip
Related Errors:
0022
Description:
This error is caused by a cold solder joint under the GPU, (H)ANA-chip or in between.Can also be a component that is missing or damaged so look for missing parts near the GPU and the (H)ANA chip.
References:
No references available...
Known fixes:
1)If you worked on the mainboard recently(soldered or so) remove these wires because you might be drawing too much power from the GPU
Also look for missing/bridged components like capacitors/resistors
2) X-Clamp replaceme
已知修正：
1）如果您在任何焊接主板发生之前，无论你是从这个角度供电正在制定的权力太大，以便摆脱it.Also摆脱去除所有，你可以看到，大桥可能GPU附近的任何东西。
2）X光钳替代混合-螺丝拧紧了GPU面临的高清音视频芯片略多...
3）回笼用在GPU和（H）全日空芯片heatgun（精矿焊料
相关错误：
0022
描述：
此错误是由冷焊料的GPU联合下造成的，（高）全日空芯片或between.Can也是一个组件，丢失或损坏，以便寻找失踪近GPU和（高）全日空芯片部分。
参考文献：
没有可参考...
已知修正：
1）如果您在主板上的工作最近（焊接左右），删除这些电线，因为你也许从GPU的权力太大
同时寻找失踪/桥接电容器等元件/电阻
2）X光钳替代
3）用酒精冲洗，让干燥，开始象下面这样的通量Relow
4）回笼用heatgun焊料的CPU / GPU / RAM区
相关错误：
相对误差不..
描述：
此错误是由一个桥接焊料在CPU，GPU或RAM的bricks.It一个联合也可以与权力（在CPU / GPU或记忆体原位缺口得到足够的功率）也可以是一个组件，丢失或损坏，因此，期待在GPU附近失踪，桥部件
已知修正：
1）取出下桥电容短路的GPU
2）X光钳替代
3）回笼用heatgun焊“”“”的CPU / GPU / RAM区
相关错误：
0102
描述：
此错误可以是由感冒引起的焊料在GPU或桥接电容器联